Antec C8, RTX 40 GPU Support, Independent PSU Cooling, Type-C 10Gbps Port, Seamless Tempered Glass Side Panels, 360mm Radiator Support, Full-Tower E-ATX PC Case

始めてパソコンの組み立てを行った初心者です。 ケースが大きめで内部構造が二層式になっているので、内部で伸びるコードの処置がやりやすく、大きな苦労なく組み上げることができました。 見た目は、木目調な部分が美しく、正面からサイドにつながるガラス面も綺麗なカーブが所有感を上げてくれるようです。 難点を挙げるとすれば、大きいということでしょうか。 当方、デスクの足元に設置しているので特に支障はありませんが、デスク上に置くとなるとなかなかな圧迫感があるもしれません。 （ただ、デスク下だとせっかくの美しい筐体があまり目に入ってこないので、それはそれで寂しかったりもします） 総じて大満足な買い物でした。

似たようなピラーレスケースは他にもありますが、前面のウッドパネルのお洒落さに一目惚れして購入しました。 組みやすさとメンテナンスしやすさも申し分ない上でやはりデザインが良いことが一番気に入っています。 あと地味に天面に電源スイッチやUSBポートがある点も気に入っています。

This is a VERY high quality case. Much better quality than you'll find from the similar Corsair 6500D that costs almost double. GamersNexus did a good review of it with positive response. The wood looks great with no flaws. The panels all fit together nicely, the glass fits nicely, it can take a lot of fans AND 3x 360mm rads, the back side allows for lots of cable management...I have zero complaints with this case. I previously ran a full custom water loop with 2x 360mm Corsair XR5 radiators and they fit great with TONS of room, and room for another 360mm rad. Currently running 12 fans in it with push/pull on an AIO rad. It's a seriously good case.

I was stuck between two choices- this and the NZXT H6 Flow and chose this. Whole thing is built like a tank. Every single panel is sturdy, despite of the top panel not having any support at one end. This is a big boy. A lot of glass area, roomy PSU chamber, The O11 vibe is there. building in it was absolutely a breeze. It has ample room for cable management- even with a non modular PSU, you can easily manage the cables without resorting to jamming them up against the side panel. Speaking of the side panel, it is all vented. Main chamber is very wide too. Internal mounting mechanisms are top notch. Every HDD partitions have vibration dampening, PSU mounting is in a perfect spot so that cables reach on both ends of the motherboard well. With all that said, I found the external screw tolerances to be a bit on the tighter side- the PSU screw holes to be precise. I managed to scrape some paint off the case trying to insert a screw. Screw allignments are also a bit off. Also, the SSD caddies had thumb screws placed in such a way that if you put two of them in, one of the SATA power cable will interfere with it. Another point I noticed is the absence of a standby light. There is basically no way of knowing if the system is on unless any of your RGB stay on by default. Overall, this is one of the best cases you can build in. It is big, sturdy and roomy.

This case is huge, but it fits all of my components very well. Even a big 3 fan 7900XTX fits with lots of room to spare.