be quiet! DC2 Pro Thermal Grease for High-end Chips | Liquid Metal | 80W/mK | for Over 10 Applications | BZ005

great product works well and does a good job of dispelling heat from the processor delivered fast

Takes a lot of patience to apply correctly but its well worth it. I had to underclock my 13700k with a massive cooler so it wouldnt run at 100 under a slight load, now its back at stock and rarely hits 90. what a freaking improvement. never using regular ol paste again!

Yes, as other reviews have commented, difficult to spread as it initially balls up on CPU. Continue wiping with q-tip and it will eventually spread. Don't use to much. When finished, it dropped my cooler by 8-10C degrees over Corsair's stock paste. It was what I was hoping for. If it wasn't so time consuming to spread, I would give it 5 stars.

I'm sure the OEM factory paste is crap, and applied by Ray Charles. So doing this was needed. After removing the old, cleaning and prepping for the new. It went on with ease and control. Applied to all the "spicy" parts of the mobo and slapped it back together. I took temp readings before and after. Doing a 4K video compression/edit. 15deg cooler with the new goop. (Pro Tip) Pull the plunger back a bit. Shake to remove a bit of the separation. (Oil/paste thermal pre-cum looking stuff).

I've been locked in on thermal grizzly's Conductonaut LM for a long time now, but this stuff is much less expensive and performs just as well. The packaging also includes the same nice to haves as those more expensive TG LMs; the packaging includes special q-tips for spreading the LM, and a few other goodies. I'm very happy with my purchase.

I was happy at first. It was very easy to apply, and only a tiny amount was needed... 3 drops. It worked great for six months! Then I noticed that a small amount had leaked out there were super tiny metal droplets (<1/4mm) on the memory modules below. This thermal compound never sets up or thickens, it stays very runny forever. Cleaning it up was a huge pain.

Not only did I get the highest scores I've ever seen, but my setting never got above 55c (Ryzen 9 9950X 16-Core)! I will be buying it for the rest of my life!

Spread this out on a gaming laptop with an i7/4070 combo. Temps dropped by nearly 10c on average and overall I'm happy with the results. When applying the liquid you need to be careful on how much pressure you use to apply because it decided that most would com out all at once. Also once you get it out the liquid compared to thermal paste was not as easy to spread. If you are new to this you should watch a video on how to. Other than that once you get used to it its easy.

I bought this as it was recommended on the BeQuiet website to use with the Dark Rock Pro 5 cooler, which turned out to be a terrible decision. The thermal "grease" just beaded up on the CPU, and was impossible to spread with the included tool. It was very difficult to remove as it is very thin. While I had removed all traces from the CPU, both the CPU and motherboard no longer worked. Even the tiniest trace amount left in the wrong place will destroy your system. This is well known, and Intel recommends against using liquid metal and voids the warranty if used. I am disappointed that the manufacturer on their website, the manual and instruction video does not adequately explain the very high difficulty in using the product, and the inherent very high risk of serious damage if the user gets it wrong

Alles prima, Top Produkt.

Ce produit est très liquide. Il ne faut pas déborder en l'appliquant. Sinon je toucherai plus à l' installation du processeur, une garantie presque à vie du système de refroidissement Noctua. Je valide mon achat.

This is the latest Liquid metal thermal grease from beQuiet and the package contains the grease syringe, syringe needle, cotton swabs (x2) and 2 isopropyl alcohol cleaning swabs. The instructions include a 'caution' that you must not use the grease on heat-pipe direct touch coolers or aluminium surfaces. It states the thermal grease is also electrically conductive. Suitable for use on copper, gold, silver, lead and zinc and harmless for nickel-plated surfaces. I hope this information helps.

You have to get the surface like a mirror clean before the liquid metal sticks. And no way is there enough for ten applications. The syringe is mainly full of air. Very hard to achieve a tiny amount when pressing the plunger, as it suddenly comes out unrestricted, because the plunger is pushing against air. Apart from all this my cpu runs 8 degrees cooler. I did want to use it on my graphics card but I didn't have enough.