iUniker Raspberry Pi 3B+ Case - Transparent with Heatsink - Access to All Ports

I'm gonna go ahead and give 5 stars because I really like this little case. Simple snap together fit, fits the board great, and it seems well built enough. I will admit I bought this quikly without verifying which boards it fit, and I have a Pi 4. Soooo, I cut the case with a utility knife to fit the ports correctly. Whoops. Still a great, simple little case, tho! :)

The iUniker black case was a nice surprise to enclose my DMR hotspot project using a Raspberry Pi B 3+ and MMDVM HAT board that sits on the GPIO connector. The upper case slot allows the GPIO connected board to seat correctly with about 1/8 inch clearance above the LCD screen, which I only used to set up the hotspot. I did have to drill a hole through the top of the case for the MMDVM board's SMA connector but that was easily done. The ABS plastic case is very sturdy and much stronger than other cases I have used with other projects. This will be my go-to case for future projects! Highly recommended for its sturdiness and layout.

I bought this case to house a Rock64 single board computer. It is the same size as a Raspberry Pi 3 but some of the ports are in slightly different locations. Because of this I had to make some modifications to the case which would not be needed for a Raspberry Pi: 1 - Around the micro USB port (the Rock64 board uses a barrel connector) 2 - Near the GPIO ports (the Rock 64 board has another 2 rows of pins) 3 - Around the headphone jack (the Rock64 board's headphone jack was in a slightly different position) 4 - Near the MicroSD slot to accommodate the Rock64's power and reset buttons The GPIO pins are fully exposed, making it easy to connect wires to or to connect a ribbon cable for a breakout board. The rubber feet included in the package keeps the case from sliding around, while the included heatsinks keep the processor and memory cool. If I had a Raspberry Pi that needed a case I wouln't hesitate to buy one of these cases for it.

I am using this for a Libre Le Potato board and it fits just fine. I did have to bend the IR receiver back just a touch. Not a biggie since I am not using it, and it may still work as it is in this clear case (maybe) or just drill out a small hole where the receiver is. The 2 included heatsinks (one larger than the other) are not as useful for the La Potato since there are 3 chips on the topside. I already had some aluminum ones that work, so used those instead. If you have a Pi 3, they will be helpful, and even on the Le Potato the larger heatsink would work. I bought this case because of the openness of it, not for the GPIO access. I wanted something with at least semi decent passive airflow vs. fully enclosed cases. I did not want a fan, so this seems to fit the bill. My unit is used as a Pi-Hole so is not very hot, but no need to make it hotter by putting it in an unventilated case. It is running around 46°C (114°F) with cheap aluminum heatsinks in the case velcroed to the side of a desk. Ambient is ~ 77°, and no real airflow in the area. Only reason it is not 5 stars is one of the mounting screw mounts did not have a hole in it so I could not screw that one in. Sure I could have taken the board back out (I had done 3 of the 4 screws already), found the right size drill bit, and hope to drill a hole correctly and reinstall, or as I did, just leave the 3 screws in place and not worry about it. I am not moving this case around anywhere so no huge deal, but still should not have happened.

Plain and simply, this case just does exactly what you would expect. It's a durable clear case that was meant to keep your Raspberry Pi safe and it does a damn good job of that. It was extremely easy to assemble. Literally just follow the cases mold and put your Pi in. The case clicks shut and holds the Pi well. There are also 5 screws (1 extra) to hold your board to bottom steady but it doesn't seem neccessary as there is no wiggle room inside the case. The rubber feet are a nice addition as well and just sticker on the bottom in the corners. Lastly it comes with 2 heat sinks but I didn't find myself using these as I already had my two for my Pi but maybe if I decide to get another Pi this will be handy. There are plenty of cases built specifically for the Raspberry Pi and you would be fine purchasing those as well but if you were looking something that is just simple and easy to setup then you won't go wrong here.

Impressed. Whoever designed this actually cared. I paid $7, and thought I would feel like it was the cheapest thing I could get. Great fit, feels secure and sturdy, easy to mount if you wanted, it has labels for all the ports, easy to access the micro sd card, an extra screw if you lose one, little rubber feet, and the heat sinks. Happy buy. It's not as crystal clear as the pictures

Solid case, no problems. Highly recommended.

A good case for the RaspberryPi 3, as it is very simple to assemble, and is a perfect fit for the RPi 3. A power adapter is a necessity, to power the RPi 3

Buen diseño para el RB3PI+ considero un poco alto el costo, sin embargo revisando en otras fechas el producto puede bajar

Easy to install case. Spare screw and silicon non skid bumps in zip lock bag. Heat sink tip. Adhesive backing cover, use some masking tape to peel

Me encanto es justo como se describe y como aparece en las imagenes