Nelyrho 3-Burner Propane Forge Kit with Double Doors, 2600°F Max

First off, I gave it a five-star rating because of the price. Are there "better" forges available? Undoubtedly; but they will cost a LOT more than this Nelyrho. I usually use a vintage coal burner, but needed something portable and handy for demonstrations and training Scouts. This guy fits the bill! I did several applications of ridgizer and then multiple thin coats of refractory cement. Noting that it had no "chokes" for the burners, I fabricated a couple using copper tubing - TOTALLY unnecessary. The burners fairly roar - and generate plenty of heat. A possible improvement might be valve for at least one burner for the times you need to heat a small piece; I may end up adding them to both. As an aside, I happened to have a Camp Chef Portable Dutch Oven Table on hand. Without the wind shield it makes a perfect stand, and is also available on Amazon.

Incredible. My son is obsessed. Absolutely lives up to it reputation. Wouldn’t buy any other make.

Awesome forger and very affordable! Works great! My son uses it for his farrier business and making horse shoes and knives. Very easy to use.

This forged arrived early, but it had one broken part. It was one of the ceramic insulating rings where the burners connect. Not only did the manufacturer get back to me in an hour or so. But they sent me 3 new ones that arrived a day or two earlier than they said. Excellent customer support. And, the forge works perfectly. Would buy again.

👍

The forge has been pretty good for me. I did line it with refractory cement. Only reason it isn't 5 stars is that I've had to replacement some orings in the hoses because they were leaking.

Really great. Just rigidize, and coat with satanite 2x. Make the satanite like slip (clay technique, look it up) and coat the tough to reach spots with a smaller paint brush, and or paint the whole thing in thin coats. Don’t overthink mixing the mortar just add a little water, mix and examine for smoothness. Mix well and dab on with a brush or use gloved hands. Good luck. Rush version: paint a coat of satanite, dry with hair dryer 10 minutes, fire with propane until solid. Step 2 Repair cracked parts from rushing. (This how I did it and in 3rd coat is now perfect). You can add plistix ( or another infrared reflecting coating on top for the best efficiency and heat). Good luck!

If you've been forging for a bit and found yourself thinking that you'd probably be able to do a lot more if only your little single burner forge was bigger, this is a decent choice. The burners are as basic as they get...there is no air adjustment, just a calibrated hole for a particular pressure, so don't expect to make a reducing or oxidizing flame. The bricks are good quality and so is the build quality, can't really find a fault in the forge itself at this time, though I haven't used it much. The one thing I'd like to point out is that the ad shows that no additional coating is necessary, but that's horse apples. It comes with kaowool inside that needs a rigidizer and (optionally) refractory cement, says so in their instruction sheet and it's obviously untreated kaowool. You need that rigidizer unless you'd like to be inhaling those fun particulates that burn off and get in the atmosphere around you, basically diet asbestos when you're forging. Refractory cement will help it last a whole lot longer but isn't necessary like the rigidizer is. A bit disappointed as I thinking it was pre-rigidized or something, so I didn't order any rigidizer. Don't make the same mistake, buy the coatings along with your new forge so you don't have to wait to use it.

Great product great price

Great purchase my husband likes it alot very good

Works great. Lots of heat hoses are far enough away they will not get hot or melt

Heat is hard to optimize in this design. Good to learn tough but i would.go.with a smaller one on this type of.frame. also the door are a pain to deal with, heat deform the door making the wool pop out..

Takes a little getting used to but thats the idea I think. Learn as you go. Fantastic starter introduction forge for a beginner. Your not making swords or armour in this but for small knives etc its perfect