YIHUA 929D-V

Neat tool, good item and works very well. I am an electronics guy and had been using a normal soldering iron in 1 hand and a desoldering pump in the other hand for decades. Never ideal, but it worked. I bought this because other reviews had recommended it to me here. I bought it, tried it, and have been using it a lot. So far, so good. It gets hot enough to melt the solder well, and having the suction in the middle of the tip works a lot better than the separate combo does. Also, since you can use this with one hand, and that includes reloading the suction spring, it frees up the other hand to hold components or whatever. Good buy, well worth it. The only thong I am concerned about is if and when the sucker gets stopped up or filled up, I don't see an easy way to take it apart and clean it.

My step-son's Switch controller needed a new joystick. As an amateur electronics kit builder, I figured, "no problem", but there were 14 pins needing to be un-soldered. I've used a solder-sucker before, but this looked like it might be too much work for what I had. This tool served as both the soldering iron and sucker at the same time, so no switching back-and-forth. For this reason, it would be worth the price if I expected to use it often. For me, it will probably get used only very occasionally, but it's nice to keep with the other DIY electronic tools just in case. It was easy to clean out the bits, and at came with three extra tips, though I haven't needed any others than the one installed. It had enough power to melt the solder on both sides of the PCB, and sucked it right through the hole, needing to be re-applied on only a few of the 14 pins. It's handle was very ergonomic, fitting my hand well, making it easy to de-solder and trigger the suction with one hand. The only problem that took getting used to was holding the tip against the PCB. The spring action of the piston tended to make the tip bounce off of the board, preventing the suction from working. Some careful pressure solved that problem with a few tries.

This YiHua desoldering iron is a pretty solid tool. It's super easy to use and heats up quickly, melting solder in a flash. The metal tip is a big improvement over those teflon ones that always seem to burn or melt. Plus, it's easy to clean and doesn't clog up easily. For it's current price point, it's a good middle-ground option between those cheap solder suckers and the pricier desoldering guns. Now, here's the thing: it works way better than those manual solder suckers, but it doesn't have the super-powerful suction I was hoping for. For components with two leads, it usually gets the solder out in one go. But sometimes it takes a few tries, even with through-hole contacts. With bigger components, like transistors or capacitors, you'll probably need to do several cycles of melting and sucking to get all the solder out. Holding it on the joint for longer helps melt the solder thoroughly, but be careful not to overheat the component. I didn't have any issues with the tip fitting over different sized leads, from tiny resistors to larger transistors and capacitors. It works best on two-lead components because the leads can move freely as the solder melts. With three-lead components, it's a bit trickier. Overall, this tool is definitely a step up from a basic solder sucker, but don't expect the same vaccum as one one a complete rework station. If you're looking for a decent, affordable desoldering tool, this one gets the job done, just be prepared to put in a bit of extra work on those stubborn joints. --- Product: YiHua 929D-V Electric Desoldering Soldering Iron Solder Sucker Desoldering Pump with Shorter Charging Handle and Desoldering Nozzles 1.0mm 1.2mm for Through-Hole Desoldering ASIN: B094ZCRXMN

Really happy with this. Was able to desolder with ease. I have soldering experience as a hobbyist, but have always struggled a bit more with de soldering. Got job done, removed joystick module from Xbox controller and installed TMR sticks. Would definitely recommend and would purchase again. I haven’t used long enough to see longevity but seems well built for the cost.

Comes with different size tips. This is perfect for de-soldering components from a circuit board. It even worked for metal mounting tabs, like on slide switches. Easy to use. Small sponge and stand are included. Worth the money.

Satisfied with this solder sucker. Heat level is sufficient, heats up quickly, not too large so it is easy to hold, pump vacuum seems fine, effectively removes solder, nozzles unscrew easily.

The unit functions well, but is lacking in key features. First and foremost, there is no power or heat adjustment. It's on as soon as you plug it in at whatever temp is heats to at your local voltages. Second, the little stand it comes with is woefully inadequate. If you are going to use this with any regularity, you need to purchase a better stand. Leaving it sit on the table on that little wire stand nearly caused a panic attack. For the price, its a good and handy tool that will save you a lot of effort and solder wick.

Good product. easy to use. Does the job well. Good value

Hasta el momento a sido de gran ayuda. Facilidad al desoldar componentes electrónicos.. Muy práctico funciona bien. Ahorra tiempo....👍