OSTENT Full Housing Shell Faceplate Case Repair Replacement for Sony PSP 3000 Console Color Green

Dont buy, it garbage. The joystick and direction pad not work. The shell is loose and dont fit properly. There was no hole for the umd spring so the umd door is loose. The left and right bumper is loose. This is some terrible product they ever made.

I just bought this for parts that I need for the spirited green PSP. If you are looking for a full case swap, LET THE PROFESSIONALS DO IT. It's not a do-it-yourself project. Other then that, it's a great way to set yourself apart.

The positives: — This shell is very attractive, and the paint job appears to be high quality. Placed side-by-side with the OEM shell it was meant to replace, I'd say the hue was 95% accurate to the official Sony shell. — The UMD door spring assembly and latch were also well designed. I found them much easier to install than in the OEM case. They felt sturdy as well. — The power button slider is very similar to OEM. This is the only 3000 series PSP I own, but when I swapped shells on my 1000 series, I returned a few units because the slider was integrated into the back shell and very flimsy. The negatives: — The trim, especially on the bottom edge where the left and right halves meet, is very fragile. They are meant to snap in place via tiny plastic clips, however the clips are made of a similar plastic to those snap together model kits I put together as a grade school kid a decade before the first PSP was released. No matter how careful you are, chances are high one will snap off. This leads the trim to bow out because the plastic is too cheap to hold its own form without clipping in. — The front and back shells do not sit flush. I removed the faceplate probably a half-dozen times before I accepted that it was a design flaw and not user error. The poor fit is distractingly unattractive for a perfectionist like me, but even if others are OK with it, it makes using the system difficult. If it were any worse it would be impossible. This is because the 1 mm to 1.5 mm gap is enough to impede the analog stick. Also, though it did not effect gameplay, I had push the front and back shells together to hit the PlayStation and volume buttons. — The body plastic is low quality as well. Compared to this, the OEM case feels like one of those anodized aluminum Gameboy shells. This would not be an issue if the shell were a good fit, but to deal with the control issues, I found myself holding the PSP with a death grip. This further strains the plastic and makes the aforementioned issues even worse. Conclusion: If you plan to put your PSP on a pedestal, this case is undeniably attractive. If you plan to play it, you should look elsewhere. This is the second brand of PSP 3000 shell I have tried and the other was of similar quality. If your current shell is too damaged to play, my advice would be to get a good condition used OEM shell and learn to live with the scuffs. Returning this was one of the easiest decisions I've ever made.

The shell is very well made and is identical to that of the original Sony shell. Very high quality material, even better than my original shell. Only issue is joystick included is a little taller so makes it have a tight fit on the left side, but this is easily fixed by shaving down the base, or opting for just leaving the original black stick, As I myself have done. I recommend using the stock screws for the internals like the motherboard and the screws provided for the case and outer pieces, as I found this gave the shell the best fit. Also there is no screw tool included, i recommend getting a precision screwdriver set and other precision tools as these help greatly in disassembling the tiny and very fragile components connected to the mother board.

Color is better than I expected, that is a positive and the only reason I am rating 3 stars. PROS: Pretty color, same as a traditional green Christmas ribbon and I like that! Case feels nice in hands, but, that's all the good I can say about it... CONS: 1. Plastic molding bled around the speaker & mic holes so I had to drill them out. 2. Half the screw mounts were almost closed up and one actually was, I had to thread them manually. 3. The BIGGEST complaint?! The screen is that easy-to-scuff-even-with-cloth plastic! It even arrived pre-scuffed WITH the protective coating STILL on it! In short, I do NOT recommend this product until they at least address the issue with the screen glass (plastic). (EDIT to #3, there were TWO layers of protective film on the screen! The screen is just as clear as the original, so ignore this complaint as its no longer valid and there was no issue to address)