Wireless Remote Switch,AC 110V/120V/240V/40A Relay,Wireless RF Switch for Household Appliances,Pump,Dust Collector,Lights,and Electrical Equipment with 328ft Long Range(110V Remote Switch)

It's been installed about a week. Both remotes work well. I use it on a dust collector in my shop, and so far it's worked fine from all areas of the shop. I cut the end off the power cord and wired both ends to the terminals with spades and connected the ground with a wire nut. I would prefer an end to end connection instead of side by side, but it works just fine.

This works exactly as advertised. Super easy to set up! I just wired a 120VAC male plug to the IN side and a female one to the OUT side. Plug input into the wall receptacle and the lamp (or whatever 120vac thing) into the female plug.

Perfect to run my pool lights! Mounted inside the fuse panel, between the breaker and the wires removed from it. The antenna ships coiled, but I needed it outside the enclosure. So I drilled a hole for a rubber grommet and straightened the wire to exit the box right away. This is a 1/4 wave at 433MHz, very low frequency (like bass, it travels further). I know this because my own product also uses sub1GHz radio, ISM Band. Will blow away BlueTooth for interference. No programming out of box. Both keys work the relay, and the channels can be retaught if needed. I may try my pool pump next.

Initially at least, this is a quality product and im surprised at the price, the remotes work at great distances and it was very easily installed in an exterior bollard light. Even through the aluminum it's working at least out to 100 yards. 100% better than trying to use a plug in controller and it's small enough it could replace a switch in your house or business and replace the cover to a blank. Highly recommend 👌

I installed this on a boat slip so the lights could be turned on before the boat was pulled in. Prior to this you had to tie up the boat in the dark and then get out and turn the light switch on. I installed this where the light switch was. There was no need for the light switch anymore and that was the easiest place to wire it in. The lights can now be turned on pretty far out from the dock before pulling in. I would say the distance we tested it at was at least 100ft. There's really no need for us to use it any farther away. I very much recommend this. It's super easy to install and comes with two remotes.

Works great

I have 3 of these controlling lights, and one running at 220V 1HP lawn watering pump. My only complaint is that the programing instructions with the gizmo could be better. I just set up two switches with 4 remotes. Each remote operates both switches simultaneously (they're in range of each other). To program generally I wind up hitting the learn button 8 times to start with a clean slate. There are 3 modes for programing the remote's buttons. The mode is controlled by how many times you push the learn button on the switch. One push for Momentary, two for Toggle, and three for Latched. Push the learn button once, the LED will flash once, then go steady. It's ready to read the button on the remote. Push the desired button on the remote. If it takes the switch LED will flash 3 times and turn off. Then you can check the function by holding the button on the remote and whatever is connected to the load side should operate as long as the button is being pushed. Two learn button pushes sets up Toggle. The LED flashes then goes steady waiting for a button push on a remote. LED out, push the button and see if it works. In Toggle if the switch is OFF, it turns it ON and vice versa. For a single switch I like to program both buttons to Toggle so that it doesn't matter what button is used to either turn ON or OFF. Then there's Latched which is the way the remotes are set up with the switch in the box. Push the learn button 3 times, press the button used for ON, steady LED again then the one for OFF. I like Latched mode for sending one signal to multiple switches just in case they get out of synch with each other. Discrete ON and OFF commands would help keep the switches in synch. Lot of words, but once you get the hang of programing it's really pretty simple. BTW as far as I could tell, the switch is double throw. That is both the line and neutral are interrupted when OFF/open. Another BTW is that I believe that the switch can hold 8 buttons, so 4 remotes is probably as much as it can handle.

Very easy to install worked great

It worked flawlessly, until it didn’t. The switch will turn on my dust collector but won’t shut it off anymore, after only 5 months in operation.