Bob Smith Industries BSI-157H Maxi Cure/Insta-Set Combo Pack (3 oz. Combined),Clear

I recently ordered this for the third time in as many years, and they last longer than that because I gave the first one away to a friend who needed it. This is good stuff. It is thick enough that it doesn't run, but thin enough that when you push two pieces together it spreads out and gets in the way. It will adhere and go through the 'grab and hold' we're all familier with, but it takes a moment, so you have a bit of time and leeway to work with it, but still, you have to be sure of yourself and be prepared. It can also serve as a void filler -- the spray-on accelerator gives almost instant hardening (note, it's a fine spray, it reaches beyond your aim, makes things slippery, and smells funny, though it doesn't irritate my eyes. However, it washes off easily with just plain soap and water. Not so the glue if you stick some to your fingers, so be careful, and maybe keep some acetone (fingernail polish remover) around. Anyway, this product has fixed everything from toys to containers to magnets on things to busted ceramic tiles, even a big one 20" square. I'm impressed, enough to buy it every time.

This is BEST glue I've ever used. I can at least comment on plastic. I 3d print, and used different glues with "Ok/average" success. But I had a big dragon with relatively heavy wings and akward to hold in place while glue dried. I tried different 2 part epoxy from one syringe, and tried "5 minute glue" and when I would try to glue it and do my best to prop up the wing even after hours it didn't seem to hold right. For some reason I tried this, "unknown" glue and OMG. I put a tiny glue in the whole of the wing and spray the "activator" on the male part of where the dragon wings attach and I place them together and LITERALLY 10 seconds it's hard, within a minute it's permanent. I'm AMAZED. I've used it on many different projects and it lasts a long time. This was second purchase of it. The ONLY time it's failed is my car window motor broke and window wouldn't stay up. So I tried to line a whole trail of glue on top of window and sprayed rubber part. Held window up for a minute, let go and it was fine. Lasted about a week then window came lose and dropped. I'm not sure if I didn't use enough glue or didn't spray right. Amazingly it lasted for nearly a week after only holding in place for literally a minute. But I THINK it's because I did something wrong, not the rain or heat the only day it was warm 2 weeks ago. Anyways, this stuff is amazing BUY IT if you need glue EVER. And to the creators/seller THANK YOU for making and selling such an easy to use glue.

Works wonderful, especially if your goal is to fuse your fingers together! I use this primarily for my 3d printed models. PLA, PETG

I’ve been using these products for years, learned from a woodworker. I like the fact that they have all types of thickness you can purchase. Just be careful as with any superglue you don’t want to glue your fingers together or glue your fingers to what you’re fixing. Great product!

Glue works good on scale models. I would suggest using a tooth pick to apply the accelerator as the pump is a mess to use. The whip they supply for the glue clogs easy and not worth using again easier to use a tooth pick. The smell is not bad.

Dependable product.

Best glue. I but this all the time. The zip kicker is best for modeling, being dispensed drop by drop from a needled squeeze bottle.

I'm very happy with this glue. It's the right thickness to be very versatile and can be used for just about anything. I like that the activator is a pump sprayer instead of an aerosol can as they tend to go flat before the glue is used up. The cap also has a needle to keep the opening from clogging when in storage. Bond strength and cure time is incredible!

Sick of super glue hardening in the tube after a few uses? Me too! Bob Smith Industries and their range of products is just the ticket. Non reactive plastic bottles keep the glue ready together with the zip hardener makes whatever job easy and fun.

where has this product been all my life....used it to attached a magnet to acrylic....the acctivator works very quickly and the glue is thick but still workable

Bought it since its harder to get the starbond brand here in Australia without paying an arm and a leg for them. So tried this brand and it's super good! The tips are great, and I can't believe how fast it sets when sprayed with the fast curing mist. Just be careful of fingers or skin etc! Trust me, it sticks very easily! Use this for a wooden sign and it's still going strong! Love it.

This stuff is magic for 3D printing. Successfully tested with PLA and PETG. Use the spray to eliminate the white hazing during drying.

It’s fast, I used it on broken door trim clips